kernel-ark/arch/powerpc/kernel/Makefile

101 lines
3.1 KiB
Makefile
Raw Normal View History

#
# Makefile for the linux kernel.
#
ifeq ($(CONFIG_PPC64),y)
EXTRA_CFLAGS += -mno-minimal-toc
endif
ifeq ($(CONFIG_PPC32),y)
CFLAGS_prom_init.o += -fPIC
CFLAGS_btext.o += -fPIC
endif
obj-y := semaphore.o cputable.o ptrace.o syscalls.o \
irq.o align.o signal_32.o pmc.o vdso.o \
init_task.o process.o systbl.o idle.o \
signal.o
obj-y += vdso32/
obj-$(CONFIG_PPC64) += setup_64.o binfmt_elf32.o sys_ppc32.o \
signal_64.o ptrace32.o \
paca.o cpu_setup_ppc970.o \
cpu_setup_pa6t.o \
firmware.o sysfs.o nvram_64.o
obj-$(CONFIG_PPC64) += vdso64/
obj-$(CONFIG_ALTIVEC) += vecemu.o vector.o
obj-$(CONFIG_PPC_970_NAP) += idle_power4.o
obj-$(CONFIG_PPC_OF) += of_device.o of_platform.o prom_parse.o
procfs-$(CONFIG_PPC64) := proc_ppc64.o
obj-$(CONFIG_PROC_FS) += $(procfs-y)
rtaspci-$(CONFIG_PPC64)-$(CONFIG_PCI) := rtas_pci.o
obj-$(CONFIG_PPC_RTAS) += rtas.o rtas-rtc.o $(rtaspci-y-y)
obj-$(CONFIG_RTAS_FLASH) += rtas_flash.o
obj-$(CONFIG_RTAS_PROC) += rtas-proc.o
obj-$(CONFIG_LPARCFG) += lparcfg.o
obj-$(CONFIG_IBMVIO) += vio.o
obj-$(CONFIG_IBMEBUS) += ibmebus.o
obj-$(CONFIG_GENERIC_TBSYNC) += smp-tbsync.o
obj-$(CONFIG_CRASH_DUMP) += crash_dump.o
obj-$(CONFIG_6xx) += idle_6xx.o l2cr_6xx.o cpu_setup_6xx.o
obj-$(CONFIG_TAU) += tau_6xx.o
obj-$(CONFIG_HIBERNATION) += swsusp.o suspend.o
obj32-$(CONFIG_HIBERNATION) += swsusp_32.o
obj64-$(CONFIG_HIBERNATION) += swsusp_64.o swsusp_asm64.o
obj32-$(CONFIG_MODULES) += module_32.o
ifeq ($(CONFIG_PPC_MERGE),y)
extra-$(CONFIG_PPC_STD_MMU) := head_32.o
extra-$(CONFIG_PPC64) := head_64.o
extra-$(CONFIG_40x) := head_4xx.o
extra-$(CONFIG_44x) := head_44x.o
extra-$(CONFIG_FSL_BOOKE) := head_fsl_booke.o
extra-$(CONFIG_8xx) := head_8xx.o
extra-y += vmlinux.lds
obj-y += time.o prom.o traps.o setup-common.o \
udbg.o misc.o io.o
obj-$(CONFIG_PPC32) += entry_32.o setup_32.o misc_32.o
obj-$(CONFIG_PPC64) += misc_64.o dma_64.o iommu.o
obj-$(CONFIG_PPC_MULTIPLATFORM) += prom_init.o
obj-$(CONFIG_MODULES) += ppc_ksyms.o
obj-$(CONFIG_BOOTX_TEXT) += btext.o
obj-$(CONFIG_SMP) += smp.o
obj-$(CONFIG_KPROBES) += kprobes.o
obj-$(CONFIG_PPC_UDBG_16550) += legacy_serial.o udbg_16550.o
module-$(CONFIG_PPC64) += module_64.o
obj-$(CONFIG_MODULES) += $(module-y)
[POWERPC] Rewrite IO allocation & mapping on powerpc64 This rewrites pretty much from scratch the handling of MMIO and PIO space allocations on powerpc64. The main goals are: - Get rid of imalloc and use more common code where possible - Simplify the current mess so that PIO space is allocated and mapped in a single place for PCI bridges - Handle allocation constraints of PIO for all bridges including hot plugged ones within the 2GB space reserved for IO ports, so that devices on hotplugged busses will now work with drivers that assume IO ports fit in an int. - Cleanup and separate tracking of the ISA space in the reserved low 64K of IO space. No ISA -> Nothing mapped there. I booted a cell blade with IDE on PIO and MMIO and a dual G5 so far, that's it :-) With this patch, all allocations are done using the code in mm/vmalloc.c, though we use the low level __get_vm_area with explicit start/stop constraints in order to manage separate areas for vmalloc/vmap, ioremap, and PCI IOs. This greatly simplifies a lot of things, as you can see in the diffstat of that patch :-) A new pair of functions pcibios_map/unmap_io_space() now replace all of the previous code that used to manipulate PCI IOs space. The allocation is done at mapping time, which is now called from scan_phb's, just before the devices are probed (instead of after, which is by itself a bug fix). The only other caller is the PCI hotplug code for hot adding PCI-PCI bridges (slots). imalloc is gone, as is the "sub-allocation" thing, but I do beleive that hotplug should still work in the sense that the space allocation is always done by the PHB, but if you unmap a child bus of this PHB (which seems to be possible), then the code should properly tear down all the HPTE mappings for that area of the PHB allocated IO space. I now always reserve the first 64K of IO space for the bridge with the ISA bus on it. I have moved the code for tracking ISA in a separate file which should also make it smarter if we ever are capable of hot unplugging or re-plugging an ISA bridge. This should have a side effect on platforms like powermac where VGA IOs will no longer work. This is done on purpose though as they would have worked semi-randomly before. The idea at this point is to isolate drivers that might need to access those and fix them by providing a proper function to obtain an offset to the legacy IOs of a given bus. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-06-04 05:15:36 +00:00
pci64-$(CONFIG_PPC64) += pci_64.o pci_dn.o isa-bridge.o
pci32-$(CONFIG_PPC32) := pci_32.o
obj-$(CONFIG_PCI) += $(pci64-y) $(pci32-y) pci-common.o
obj-$(CONFIG_PCI_MSI) += msi.o
kexec-$(CONFIG_PPC64) := machine_kexec_64.o
kexec-$(CONFIG_PPC32) := machine_kexec_32.o
obj-$(CONFIG_KEXEC) += machine_kexec.o crash.o $(kexec-y)
obj-$(CONFIG_AUDIT) += audit.o
obj64-$(CONFIG_AUDIT) += compat_audit.o
[POWERPC] Allow hooking of PCI MMIO & PIO accessors on 64 bits This patch reworks the way iSeries hooks on PCI IO operations (both MMIO and PIO) and provides a generic way for other platforms to do so (we have need to do that for various other platforms). While reworking the IO ops, I ended up doing some spring cleaning in io.h and eeh.h which I might want to split into 2 or 3 patches (among others, eeh.h had a lot of useless stuff in it). A side effect is that EEH for PIO should work now (it used to pass IO ports down to the eeh address check functions which is bogus). Also, new are MMIO "repeat" ops, which other archs like ARM already had, and that we have too now: readsb, readsw, readsl, writesb, writesw, writesl. In the long run, I might also make EEH use the hooks instead of wrapping at the toplevel, which would make things even cleaner and relegate EEH completely in platforms/iseries, but we have to measure the performance impact there (though it's really only on MMIO reads) Since I also need to hook on ioremap, I shuffled the functions a bit there. I introduced ioremap_flags() to use by drivers who want to pass explicit flags to ioremap (and it can be hooked). The old __ioremap() is still there as a low level and cannot be hooked, thus drivers who use it should migrate unless they know they want the low level version. The patch "arch provides generic iomap missing accessors" (should be number 4 in this series) is a pre-requisite to provide full iomap API support with this patch. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-11-11 06:25:10 +00:00
ifneq ($(CONFIG_PPC_INDIRECT_IO),y)
obj-y += iomap.o
[POWERPC] Allow hooking of PCI MMIO & PIO accessors on 64 bits This patch reworks the way iSeries hooks on PCI IO operations (both MMIO and PIO) and provides a generic way for other platforms to do so (we have need to do that for various other platforms). While reworking the IO ops, I ended up doing some spring cleaning in io.h and eeh.h which I might want to split into 2 or 3 patches (among others, eeh.h had a lot of useless stuff in it). A side effect is that EEH for PIO should work now (it used to pass IO ports down to the eeh address check functions which is bogus). Also, new are MMIO "repeat" ops, which other archs like ARM already had, and that we have too now: readsb, readsw, readsl, writesb, writesw, writesl. In the long run, I might also make EEH use the hooks instead of wrapping at the toplevel, which would make things even cleaner and relegate EEH completely in platforms/iseries, but we have to measure the performance impact there (though it's really only on MMIO reads) Since I also need to hook on ioremap, I shuffled the functions a bit there. I introduced ioremap_flags() to use by drivers who want to pass explicit flags to ioremap (and it can be hooked). The old __ioremap() is still there as a low level and cannot be hooked, thus drivers who use it should migrate unless they know they want the low level version. The patch "arch provides generic iomap missing accessors" (should be number 4 in this series) is a pre-requisite to provide full iomap API support with this patch. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-11-11 06:25:10 +00:00
endif
ifeq ($(CONFIG_PPC_ISERIES),y)
CFLAGS_lparmap.s += -g0
extra-y += lparmap.s
$(obj)/head_64.o: $(obj)/lparmap.s
AFLAGS_head_64.o += -I$(obj)
endif
else
# stuff used from here for ARCH=ppc
smpobj-$(CONFIG_SMP) += smp.o
endif
[PATCH] powerpc: Fix handling of fpscr on 64-bit The recent merge of fpu.S broken the handling of fpscr for ARCH=powerpc and CONFIG_PPC64=y. FP registers could be corrupted, leading to strange random application crashes. The confusion arises, because the thread_struct has (and requires) a 64-bit area to save the fpscr, because we use load/store double instructions to get it in to/out of the FPU. However, only the low 32-bits are actually used, so we want to treat it as a 32-bit quantity when manipulating its bits to avoid extra load/stores on 32-bit. This patch replaces the current definition with a structure of two 32-bit quantities (pad and val), to clarify things as much as is possible. The 'val' field is used when manipulating bits, the structure itself is used when obtaining the address for loading/unloading the value from the FPU. While we're at it, consolidate the 4 (!) almost identical versions of cvt_fd() and cvt_df() (arch/ppc/kernel/misc.S, arch/ppc64/kernel/misc.S, arch/powerpc/kernel/misc_32.S, arch/powerpc/kernel/misc_64.S) into a single version in fpu.S. The new version takes a pointer to thread_struct and applies the correct offset itself, rather than a pointer to the fpscr field itself, again to avoid confusion as to which is the correct field to use. Finally, this patch makes ARCH=ppc64 also use the consolidated fpu.S code, which it previously did not. Built for G5 (ARCH=ppc64 and ARCH=powerpc), 32-bit powermac (ARCH=ppc and ARCH=powerpc) and Walnut (ARCH=ppc, CONFIG_MATH_EMULATION=y). Booted on G5 (ARCH=powerpc) and things which previously fell over no longer do. Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-10-27 06:27:25 +00:00
obj-$(CONFIG_PPC32) += $(obj32-y)
obj-$(CONFIG_PPC64) += $(obj64-y)
[PATCH] powerpc: Fix handling of fpscr on 64-bit The recent merge of fpu.S broken the handling of fpscr for ARCH=powerpc and CONFIG_PPC64=y. FP registers could be corrupted, leading to strange random application crashes. The confusion arises, because the thread_struct has (and requires) a 64-bit area to save the fpscr, because we use load/store double instructions to get it in to/out of the FPU. However, only the low 32-bits are actually used, so we want to treat it as a 32-bit quantity when manipulating its bits to avoid extra load/stores on 32-bit. This patch replaces the current definition with a structure of two 32-bit quantities (pad and val), to clarify things as much as is possible. The 'val' field is used when manipulating bits, the structure itself is used when obtaining the address for loading/unloading the value from the FPU. While we're at it, consolidate the 4 (!) almost identical versions of cvt_fd() and cvt_df() (arch/ppc/kernel/misc.S, arch/ppc64/kernel/misc.S, arch/powerpc/kernel/misc_32.S, arch/powerpc/kernel/misc_64.S) into a single version in fpu.S. The new version takes a pointer to thread_struct and applies the correct offset itself, rather than a pointer to the fpscr field itself, again to avoid confusion as to which is the correct field to use. Finally, this patch makes ARCH=ppc64 also use the consolidated fpu.S code, which it previously did not. Built for G5 (ARCH=ppc64 and ARCH=powerpc), 32-bit powermac (ARCH=ppc and ARCH=powerpc) and Walnut (ARCH=ppc, CONFIG_MATH_EMULATION=y). Booted on G5 (ARCH=powerpc) and things which previously fell over no longer do. Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-10-27 06:27:25 +00:00
extra-$(CONFIG_PPC_FPU) += fpu.o
extra-$(CONFIG_PPC64) += entry_64.o