kernel-ark/drivers/ide/pci/amd74xx.c

386 lines
12 KiB
C
Raw Normal View History

/*
* Version 2.24
*
* AMD 755/756/766/8111 and nVidia nForce/2/2s/3/3s/CK804/MCP04
* IDE driver for Linux.
*
* Copyright (c) 2000-2002 Vojtech Pavlik
* Copyright (c) 2007 Bartlomiej Zolnierkiewicz
*
* Based on the work of:
* Andre Hedrick
*/
/*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2 as published by
* the Free Software Foundation.
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/ioport.h>
#include <linux/blkdev.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/ide.h>
#include <asm/io.h>
#include "ide-timing.h"
#define AMD_IDE_CONFIG (0x01 + amd_config->base)
#define AMD_CABLE_DETECT (0x02 + amd_config->base)
#define AMD_DRIVE_TIMING (0x08 + amd_config->base)
#define AMD_8BIT_TIMING (0x0e + amd_config->base)
#define AMD_ADDRESS_SETUP (0x0c + amd_config->base)
#define AMD_UDMA_TIMING (0x10 + amd_config->base)
#define AMD_CHECK_SWDMA 0x08
#define AMD_BAD_SWDMA 0x10
#define AMD_BAD_FIFO 0x20
#define AMD_CHECK_SERENADE 0x40
/*
* AMD SouthBridge chips.
*/
static struct amd_ide_chip {
unsigned short id;
u8 base;
u8 udma_mask;
u8 flags;
} amd_ide_chips[] = {
{ PCI_DEVICE_ID_AMD_COBRA_7401, 0x40, ATA_UDMA2, AMD_BAD_SWDMA },
{ PCI_DEVICE_ID_AMD_VIPER_7409, 0x40, ATA_UDMA4, AMD_CHECK_SWDMA },
{ PCI_DEVICE_ID_AMD_VIPER_7411, 0x40, ATA_UDMA5, AMD_BAD_FIFO },
{ PCI_DEVICE_ID_AMD_OPUS_7441, 0x40, ATA_UDMA5, },
{ PCI_DEVICE_ID_AMD_8111_IDE, 0x40, ATA_UDMA6, AMD_CHECK_SERENADE },
{ PCI_DEVICE_ID_NVIDIA_NFORCE_IDE, 0x50, ATA_UDMA5, },
{ PCI_DEVICE_ID_NVIDIA_NFORCE2_IDE, 0x50, ATA_UDMA6, },
{ PCI_DEVICE_ID_NVIDIA_NFORCE2S_IDE, 0x50, ATA_UDMA6, },
{ PCI_DEVICE_ID_NVIDIA_NFORCE2S_SATA, 0x50, ATA_UDMA6, },
{ PCI_DEVICE_ID_NVIDIA_NFORCE3_IDE, 0x50, ATA_UDMA6, },
{ PCI_DEVICE_ID_NVIDIA_NFORCE3S_IDE, 0x50, ATA_UDMA6, },
{ PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA, 0x50, ATA_UDMA6, },
{ PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA2, 0x50, ATA_UDMA6, },
{ PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_IDE, 0x50, ATA_UDMA6, },
{ PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_IDE, 0x50, ATA_UDMA6, },
{ PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE, 0x50, ATA_UDMA6, },
{ PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE, 0x50, ATA_UDMA6, },
{ PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_IDE, 0x50, ATA_UDMA6, },
{ PCI_DEVICE_ID_NVIDIA_NFORCE_MCP65_IDE, 0x50, ATA_UDMA6, },
{ PCI_DEVICE_ID_NVIDIA_NFORCE_MCP67_IDE, 0x50, ATA_UDMA6, },
{ PCI_DEVICE_ID_NVIDIA_NFORCE_MCP73_IDE, 0x50, ATA_UDMA6, },
{ PCI_DEVICE_ID_NVIDIA_NFORCE_MCP77_IDE, 0x50, ATA_UDMA6, },
{ PCI_DEVICE_ID_AMD_CS5536_IDE, 0x40, ATA_UDMA5, },
{ 0 }
};
static struct amd_ide_chip *amd_config;
static const struct ide_port_info *amd_chipset;
static unsigned int amd_80w;
static unsigned int amd_clock;
static char *amd_dma[] = { "16", "25", "33", "44", "66", "100", "133" };
static unsigned char amd_cyc2udma[] = { 6, 6, 5, 4, 0, 1, 1, 2, 2, 3, 3, 3, 3, 3, 3, 7 };
/*
* amd_set_speed() writes timing values to the chipset registers
*/
static void amd_set_speed(struct pci_dev *dev, unsigned char dn, struct ide_timing *timing)
{
unsigned char t;
pci_read_config_byte(dev, AMD_ADDRESS_SETUP, &t);
t = (t & ~(3 << ((3 - dn) << 1))) | ((FIT(timing->setup, 1, 4) - 1) << ((3 - dn) << 1));
pci_write_config_byte(dev, AMD_ADDRESS_SETUP, t);
pci_write_config_byte(dev, AMD_8BIT_TIMING + (1 - (dn >> 1)),
((FIT(timing->act8b, 1, 16) - 1) << 4) | (FIT(timing->rec8b, 1, 16) - 1));
pci_write_config_byte(dev, AMD_DRIVE_TIMING + (3 - dn),
((FIT(timing->active, 1, 16) - 1) << 4) | (FIT(timing->recover, 1, 16) - 1));
switch (amd_config->udma_mask) {
case ATA_UDMA2: t = timing->udma ? (0xc0 | (FIT(timing->udma, 2, 5) - 2)) : 0x03; break;
case ATA_UDMA4: t = timing->udma ? (0xc0 | amd_cyc2udma[FIT(timing->udma, 2, 10)]) : 0x03; break;
case ATA_UDMA5: t = timing->udma ? (0xc0 | amd_cyc2udma[FIT(timing->udma, 1, 10)]) : 0x03; break;
case ATA_UDMA6: t = timing->udma ? (0xc0 | amd_cyc2udma[FIT(timing->udma, 1, 15)]) : 0x03; break;
default: return;
}
pci_write_config_byte(dev, AMD_UDMA_TIMING + (3 - dn), t);
}
/*
ide: move ide_config_drive_speed() calls to upper layers (take 2) * Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16. * Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program the host for the transfer mode after programming the device. Set it in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac and via82cxxx host drivers. * Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely skip programming of host/device for the transfer mode ("smart" hosts). Set it in it821x host driver and check it in ide_tune_dma(). * Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all direct ->set_pio_mode/->speedproc users to use these helpers. * Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc methods to callers. * Rename ->speedproc method to ->set_dma_mode, make it void and update all implementations accordingly. * Update ide_set_xfer_rate() comments. * Unexport ide_config_drive_speed(). v2: * Fix issues noticed by Sergei: - export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt to setting DMA modes from sc1200_set_pio_mode() to do_special() - check IDE_HFLAG_NO_SET_MODE in ide_tune_dma() - check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode() - check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode() - return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL - don't set ->set_{pio,dma}_mode on it821x in "smart" mode - fix build problem in pmac.c - minor fixes in au1xxx-ide.c/cs5530.c/siimage.c - improve patch description Changes in behavior caused by this patch: - HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change PIO mode if it821x controller is in "smart" mode - removal of two debugging printk-s (from cs5530.c and sc1200.c) - transfer modes 0x00-0x07 passed from user space may be programmed twice on the device (not really an issue since 0x00 is not supported correctly by any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid) Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-13 15:47:51 +00:00
* amd_set_drive() computes timing values and configures the chipset
* to a desired transfer mode. It also can be called by upper layers.
*/
ide: move ide_config_drive_speed() calls to upper layers (take 2) * Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16. * Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program the host for the transfer mode after programming the device. Set it in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac and via82cxxx host drivers. * Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely skip programming of host/device for the transfer mode ("smart" hosts). Set it in it821x host driver and check it in ide_tune_dma(). * Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all direct ->set_pio_mode/->speedproc users to use these helpers. * Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc methods to callers. * Rename ->speedproc method to ->set_dma_mode, make it void and update all implementations accordingly. * Update ide_set_xfer_rate() comments. * Unexport ide_config_drive_speed(). v2: * Fix issues noticed by Sergei: - export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt to setting DMA modes from sc1200_set_pio_mode() to do_special() - check IDE_HFLAG_NO_SET_MODE in ide_tune_dma() - check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode() - check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode() - return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL - don't set ->set_{pio,dma}_mode on it821x in "smart" mode - fix build problem in pmac.c - minor fixes in au1xxx-ide.c/cs5530.c/siimage.c - improve patch description Changes in behavior caused by this patch: - HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change PIO mode if it821x controller is in "smart" mode - removal of two debugging printk-s (from cs5530.c and sc1200.c) - transfer modes 0x00-0x07 passed from user space may be programmed twice on the device (not really an issue since 0x00 is not supported correctly by any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid) Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-13 15:47:51 +00:00
static void amd_set_drive(ide_drive_t *drive, const u8 speed)
{
ide_drive_t *peer = HWIF(drive)->drives + (~drive->dn & 1);
struct ide_timing t, p;
int T, UT;
T = 1000000000 / amd_clock;
UT = (amd_config->udma_mask == ATA_UDMA2) ? T : (T / 2);
ide_timing_compute(drive, speed, &t, T, UT);
if (peer->present) {
ide_timing_compute(peer, peer->current_speed, &p, T, UT);
ide_timing_merge(&p, &t, &t, IDE_TIMING_8BIT);
}
if (speed == XFER_UDMA_5 && amd_clock <= 33333) t.udma = 1;
if (speed == XFER_UDMA_6 && amd_clock <= 33333) t.udma = 15;
amd_set_speed(HWIF(drive)->pci_dev, drive->dn, &t);
}
/*
* amd_set_pio_mode() is a callback from upper layers for PIO-only tuning.
*/
static void amd_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
amd_set_drive(drive, XFER_PIO_0 + pio);
}
/*
* The initialization callback. Here we determine the IDE chip type
* and initialize its drive independent registers.
*/
static unsigned int __devinit init_chipset_amd74xx(struct pci_dev *dev, const char *name)
{
unsigned char t;
unsigned int u;
int i;
/*
* Check for bad SWDMA.
*/
if (amd_config->flags & AMD_CHECK_SWDMA) {
if (dev->revision <= 7)
amd_config->flags |= AMD_BAD_SWDMA;
}
/*
* Check 80-wire cable presence.
*/
switch (amd_config->udma_mask) {
case ATA_UDMA6:
case ATA_UDMA5:
pci_read_config_byte(dev, AMD_CABLE_DETECT, &t);
pci_read_config_dword(dev, AMD_UDMA_TIMING, &u);
amd_80w = ((t & 0x3) ? 1 : 0) | ((t & 0xc) ? 2 : 0);
for (i = 24; i >= 0; i -= 8)
if (((u >> i) & 4) && !(amd_80w & (1 << (1 - (i >> 4))))) {
printk(KERN_WARNING "%s: BIOS didn't set cable bits correctly. Enabling workaround.\n",
amd_chipset->name);
amd_80w |= (1 << (1 - (i >> 4)));
}
break;
case ATA_UDMA4:
/* no host side cable detection */
amd_80w = 0x03;
break;
}
/*
* Take care of prefetch & postwrite.
*/
pci_read_config_byte(dev, AMD_IDE_CONFIG, &t);
pci_write_config_byte(dev, AMD_IDE_CONFIG,
(amd_config->flags & AMD_BAD_FIFO) ? (t & 0x0f) : (t | 0xf0));
/*
* Take care of incorrectly wired Serenade mainboards.
*/
if ((amd_config->flags & AMD_CHECK_SERENADE) &&
dev->subsystem_vendor == PCI_VENDOR_ID_AMD &&
dev->subsystem_device == PCI_DEVICE_ID_AMD_SERENADE)
amd_config->udma_mask = ATA_UDMA5;
/*
* Determine the system bus clock.
*/
amd_clock = system_bus_clock() * 1000;
switch (amd_clock) {
case 33000: amd_clock = 33333; break;
case 37000: amd_clock = 37500; break;
case 41000: amd_clock = 41666; break;
}
if (amd_clock < 20000 || amd_clock > 50000) {
printk(KERN_WARNING "%s: User given PCI clock speed impossible (%d), using 33 MHz instead.\n",
amd_chipset->name, amd_clock);
amd_clock = 33333;
}
/*
* Print the boot message.
*/
printk(KERN_INFO "%s: %s (rev %02x) UDMA%s controller\n",
amd_chipset->name, pci_name(dev), dev->revision,
amd_dma[fls(amd_config->udma_mask) - 1]);
return dev->irq;
}
static void __devinit init_hwif_amd74xx(ide_hwif_t *hwif)
{
if (hwif->irq == 0) /* 0 is bogus but will do for now */
hwif->irq = pci_get_legacy_ide_irq(hwif->pci_dev, hwif->channel);
hwif->set_pio_mode = &amd_set_pio_mode;
ide: move ide_config_drive_speed() calls to upper layers (take 2) * Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16. * Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program the host for the transfer mode after programming the device. Set it in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac and via82cxxx host drivers. * Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely skip programming of host/device for the transfer mode ("smart" hosts). Set it in it821x host driver and check it in ide_tune_dma(). * Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all direct ->set_pio_mode/->speedproc users to use these helpers. * Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc methods to callers. * Rename ->speedproc method to ->set_dma_mode, make it void and update all implementations accordingly. * Update ide_set_xfer_rate() comments. * Unexport ide_config_drive_speed(). v2: * Fix issues noticed by Sergei: - export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt to setting DMA modes from sc1200_set_pio_mode() to do_special() - check IDE_HFLAG_NO_SET_MODE in ide_tune_dma() - check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode() - check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode() - return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL - don't set ->set_{pio,dma}_mode on it821x in "smart" mode - fix build problem in pmac.c - minor fixes in au1xxx-ide.c/cs5530.c/siimage.c - improve patch description Changes in behavior caused by this patch: - HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change PIO mode if it821x controller is in "smart" mode - removal of two debugging printk-s (from cs5530.c and sc1200.c) - transfer modes 0x00-0x07 passed from user space may be programmed twice on the device (not really an issue since 0x00 is not supported correctly by any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid) Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-13 15:47:51 +00:00
hwif->set_dma_mode = &amd_set_drive;
if (!hwif->dma_base)
return;
hwif->ultra_mask = amd_config->udma_mask;
if (amd_config->flags & AMD_BAD_SWDMA)
hwif->swdma_mask = 0x00;
if (hwif->cbl != ATA_CBL_PATA40_SHORT) {
if ((amd_80w >> hwif->channel) & 1)
hwif->cbl = ATA_CBL_PATA80;
else
hwif->cbl = ATA_CBL_PATA40;
}
}
#define IDE_HFLAGS_AMD \
(IDE_HFLAG_PIO_NO_BLACKLIST | \
IDE_HFLAG_PIO_NO_DOWNGRADE | \
IDE_HFLAG_ABUSE_SET_DMA_MODE | \
IDE_HFLAG_POST_SET_MODE | \
IDE_HFLAG_IO_32BIT | \
IDE_HFLAG_UNMASK_IRQS | \
IDE_HFLAG_BOOTABLE)
#define DECLARE_AMD_DEV(name_str) \
{ \
.name = name_str, \
.init_chipset = init_chipset_amd74xx, \
.init_hwif = init_hwif_amd74xx, \
.enablebits = {{0x40,0x02,0x02}, {0x40,0x01,0x01}}, \
.host_flags = IDE_HFLAGS_AMD, \
.pio_mask = ATA_PIO5, \
.swdma_mask = ATA_SWDMA2, \
.mwdma_mask = ATA_MWDMA2, \
}
#define DECLARE_NV_DEV(name_str) \
{ \
.name = name_str, \
.init_chipset = init_chipset_amd74xx, \
.init_hwif = init_hwif_amd74xx, \
.enablebits = {{0x50,0x02,0x02}, {0x50,0x01,0x01}}, \
.host_flags = IDE_HFLAGS_AMD, \
.pio_mask = ATA_PIO5, \
.swdma_mask = ATA_SWDMA2, \
.mwdma_mask = ATA_MWDMA2, \
}
static const struct ide_port_info amd74xx_chipsets[] __devinitdata = {
/* 0 */ DECLARE_AMD_DEV("AMD7401"),
/* 1 */ DECLARE_AMD_DEV("AMD7409"),
/* 2 */ DECLARE_AMD_DEV("AMD7411"),
/* 3 */ DECLARE_AMD_DEV("AMD7441"),
/* 4 */ DECLARE_AMD_DEV("AMD8111"),
/* 5 */ DECLARE_NV_DEV("NFORCE"),
/* 6 */ DECLARE_NV_DEV("NFORCE2"),
/* 7 */ DECLARE_NV_DEV("NFORCE2-U400R"),
/* 8 */ DECLARE_NV_DEV("NFORCE2-U400R-SATA"),
/* 9 */ DECLARE_NV_DEV("NFORCE3-150"),
/* 10 */ DECLARE_NV_DEV("NFORCE3-250"),
/* 11 */ DECLARE_NV_DEV("NFORCE3-250-SATA"),
/* 12 */ DECLARE_NV_DEV("NFORCE3-250-SATA2"),
/* 13 */ DECLARE_NV_DEV("NFORCE-CK804"),
/* 14 */ DECLARE_NV_DEV("NFORCE-MCP04"),
/* 15 */ DECLARE_NV_DEV("NFORCE-MCP51"),
/* 16 */ DECLARE_NV_DEV("NFORCE-MCP55"),
/* 17 */ DECLARE_NV_DEV("NFORCE-MCP61"),
/* 18 */ DECLARE_NV_DEV("NFORCE-MCP65"),
/* 19 */ DECLARE_NV_DEV("NFORCE-MCP67"),
/* 20 */ DECLARE_NV_DEV("NFORCE-MCP73"),
/* 21 */ DECLARE_NV_DEV("NFORCE-MCP77"),
/* 22 */ DECLARE_AMD_DEV("AMD5536"),
};
static int __devinit amd74xx_probe(struct pci_dev *dev, const struct pci_device_id *id)
{
amd_chipset = amd74xx_chipsets + id->driver_data;
amd_config = amd_ide_chips + id->driver_data;
if (dev->device != amd_config->id) {
printk(KERN_ERR "%s: assertion 0x%02x == 0x%02x failed !\n",
pci_name(dev), dev->device, amd_config->id);
return -ENODEV;
}
return ide_setup_pci_device(dev, amd_chipset);
}
static const struct pci_device_id amd74xx_pci_tbl[] = {
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_COBRA_7401), 0 },
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_VIPER_7409), 1 },
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_VIPER_7411), 2 },
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_OPUS_7441), 3 },
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_8111_IDE), 4 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_IDE), 5 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2_IDE), 6 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_IDE), 7 },
#ifdef CONFIG_BLK_DEV_IDE_SATA
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_SATA), 8 },
#endif
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3_IDE), 9 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_IDE), 10 },
#ifdef CONFIG_BLK_DEV_IDE_SATA
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA), 11 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA2), 12 },
#endif
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_IDE), 13 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_IDE), 14 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE), 15 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE), 16 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_IDE), 17 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP65_IDE), 18 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP67_IDE), 19 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP73_IDE), 20 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP77_IDE), 21 },
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_CS5536_IDE), 22 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, amd74xx_pci_tbl);
static struct pci_driver driver = {
.name = "AMD_IDE",
.id_table = amd74xx_pci_tbl,
.probe = amd74xx_probe,
};
static int __init amd74xx_ide_init(void)
{
return ide_pci_register_driver(&driver);
}
module_init(amd74xx_ide_init);
MODULE_AUTHOR("Vojtech Pavlik");
MODULE_DESCRIPTION("AMD PCI IDE driver");
MODULE_LICENSE("GPL");