[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
/*
|
|
|
|
* Connection state tracking for netfilter. This is separated from,
|
|
|
|
* but required by, the (future) NAT layer; it can also be used by an iptables
|
|
|
|
* extension.
|
|
|
|
*
|
|
|
|
* 16 Dec 2003: Yasuyuki Kozakai @USAGI <yasuyuki.kozakai@toshiba.co.jp>
|
|
|
|
* - generalize L3 protocol dependent part.
|
|
|
|
*
|
|
|
|
* Derived from include/linux/netfiter_ipv4/ip_conntrack.h
|
|
|
|
*/
|
|
|
|
|
|
|
|
#ifndef _NF_CONNTRACK_H
|
|
|
|
#define _NF_CONNTRACK_H
|
|
|
|
|
|
|
|
#include <linux/netfilter/nf_conntrack_common.h>
|
|
|
|
|
|
|
|
#include <linux/bitops.h>
|
|
|
|
#include <linux/compiler.h>
|
2011-07-26 23:09:06 +00:00
|
|
|
#include <linux/atomic.h>
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
|
|
|
|
#include <linux/netfilter/nf_conntrack_tcp.h>
|
2008-03-20 14:15:55 +00:00
|
|
|
#include <linux/netfilter/nf_conntrack_dccp.h>
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
#include <linux/netfilter/nf_conntrack_sctp.h>
|
2006-12-03 06:09:41 +00:00
|
|
|
#include <linux/netfilter/nf_conntrack_proto_gre.h>
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
#include <net/netfilter/ipv6/nf_conntrack_icmpv6.h>
|
|
|
|
|
|
|
|
#include <net/netfilter/nf_conntrack_tuple.h>
|
|
|
|
|
|
|
|
/* per conntrack: protocol private data */
|
|
|
|
union nf_conntrack_proto {
|
|
|
|
/* insert conntrack proto private data here */
|
2008-03-20 14:15:55 +00:00
|
|
|
struct nf_ct_dccp dccp;
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
struct ip_ct_sctp sctp;
|
|
|
|
struct ip_ct_tcp tcp;
|
2006-12-03 06:09:41 +00:00
|
|
|
struct nf_ct_gre gre;
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
union nf_conntrack_expect_proto {
|
|
|
|
/* insert expect proto private data here */
|
|
|
|
};
|
|
|
|
|
|
|
|
#include <linux/types.h>
|
|
|
|
#include <linux/skbuff.h>
|
2006-12-04 04:15:30 +00:00
|
|
|
#include <linux/timer.h>
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
|
|
|
|
#ifdef CONFIG_NETFILTER_DEBUG
|
2008-04-14 09:15:51 +00:00
|
|
|
#define NF_CT_ASSERT(x) WARN_ON(!(x))
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
#else
|
|
|
|
#define NF_CT_ASSERT(x)
|
|
|
|
#endif
|
|
|
|
|
|
|
|
struct nf_conntrack_helper;
|
|
|
|
|
2008-03-26 03:09:15 +00:00
|
|
|
/* Must be kept in sync with the classes defined by helpers */
|
2010-02-11 11:30:21 +00:00
|
|
|
#define NF_CT_MAX_EXPECT_CLASSES 4
|
2008-03-26 03:09:15 +00:00
|
|
|
|
2006-03-21 01:56:32 +00:00
|
|
|
/* nf_conn feature for connections that have a helper */
|
|
|
|
struct nf_conn_help {
|
|
|
|
/* Helper. if any */
|
2010-03-09 19:59:15 +00:00
|
|
|
struct nf_conntrack_helper __rcu *helper;
|
2006-03-21 01:56:32 +00:00
|
|
|
|
2007-07-08 05:35:56 +00:00
|
|
|
struct hlist_head expectations;
|
|
|
|
|
2006-03-21 01:56:32 +00:00
|
|
|
/* Current number of expected connections */
|
2008-03-26 03:09:15 +00:00
|
|
|
u8 expecting[NF_CT_MAX_EXPECT_CLASSES];
|
2012-06-07 10:11:50 +00:00
|
|
|
|
|
|
|
/* private helper information. */
|
|
|
|
char data[];
|
2006-03-21 01:56:32 +00:00
|
|
|
};
|
|
|
|
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
#include <net/netfilter/ipv4/nf_conntrack_ipv4.h>
|
2006-11-29 01:35:15 +00:00
|
|
|
#include <net/netfilter/ipv6/nf_conntrack_ipv6.h>
|
|
|
|
|
2009-03-25 20:05:46 +00:00
|
|
|
struct nf_conn {
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
/* Usage count in here is 1 for hash table/destruct timer, 1 per skb,
|
2014-03-03 13:44:54 +00:00
|
|
|
* plus 1 for any connection(s) we are `master' for
|
|
|
|
*
|
|
|
|
* Hint, SKB address this struct and refcnt via skb->nfct and
|
|
|
|
* helpers nf_conntrack_get() and nf_conntrack_put().
|
|
|
|
* Helper nf_ct_put() equals nf_conntrack_put() by dec refcnt,
|
|
|
|
* beware nf_ct_get() is different and don't inc refcnt.
|
|
|
|
*/
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
struct nf_conntrack ct_general;
|
|
|
|
|
2014-03-03 13:45:20 +00:00
|
|
|
spinlock_t lock;
|
|
|
|
u16 cpu;
|
2009-06-10 12:32:47 +00:00
|
|
|
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
/* XXX should I move this to the tail ? - Y.K */
|
|
|
|
/* These are my tuples; original and reply */
|
|
|
|
struct nf_conntrack_tuple_hash tuplehash[IP_CT_DIR_MAX];
|
|
|
|
|
|
|
|
/* Have we seen traffic both ways yet? (bitset) */
|
|
|
|
unsigned long status;
|
|
|
|
|
2006-03-21 01:56:32 +00:00
|
|
|
/* If we were expected by an expectation, this will be it */
|
|
|
|
struct nf_conn *master;
|
|
|
|
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
/* Timer function; drops refcnt when it goes off. */
|
|
|
|
struct timer_list timeout;
|
|
|
|
|
|
|
|
#if defined(CONFIG_NF_CONNTRACK_MARK)
|
|
|
|
u_int32_t mark;
|
|
|
|
#endif
|
|
|
|
|
2006-06-09 07:31:46 +00:00
|
|
|
#ifdef CONFIG_NF_CONNTRACK_SECMARK
|
|
|
|
u_int32_t secmark;
|
|
|
|
#endif
|
|
|
|
|
2007-07-08 05:23:21 +00:00
|
|
|
/* Extensions */
|
|
|
|
struct nf_ct_ext *ext;
|
2008-10-08 09:35:02 +00:00
|
|
|
#ifdef CONFIG_NET_NS
|
|
|
|
struct net *ct_net;
|
|
|
|
#endif
|
2010-11-12 16:33:17 +00:00
|
|
|
|
|
|
|
/* Storage reserved for other modules, must be the last member */
|
|
|
|
union nf_conntrack_proto proto;
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
static inline struct nf_conn *
|
|
|
|
nf_ct_tuplehash_to_ctrack(const struct nf_conntrack_tuple_hash *hash)
|
|
|
|
{
|
|
|
|
return container_of(hash, struct nf_conn,
|
|
|
|
tuplehash[hash->tuple.dst.dir]);
|
|
|
|
}
|
|
|
|
|
2008-04-14 09:15:52 +00:00
|
|
|
static inline u_int16_t nf_ct_l3num(const struct nf_conn *ct)
|
|
|
|
{
|
|
|
|
return ct->tuplehash[IP_CT_DIR_ORIGINAL].tuple.src.l3num;
|
|
|
|
}
|
|
|
|
|
|
|
|
static inline u_int8_t nf_ct_protonum(const struct nf_conn *ct)
|
|
|
|
{
|
|
|
|
return ct->tuplehash[IP_CT_DIR_ORIGINAL].tuple.dst.protonum;
|
|
|
|
}
|
|
|
|
|
2009-06-02 18:03:35 +00:00
|
|
|
#define nf_ct_tuple(ct, dir) (&(ct)->tuplehash[dir].tuple)
|
|
|
|
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
/* get master conntrack via master expectation */
|
|
|
|
#define master_ct(conntr) (conntr->master)
|
|
|
|
|
2008-10-08 09:35:02 +00:00
|
|
|
extern struct net init_net;
|
|
|
|
|
|
|
|
static inline struct net *nf_ct_net(const struct nf_conn *ct)
|
|
|
|
{
|
2010-06-01 06:51:19 +00:00
|
|
|
return read_pnet(&ct->ct_net);
|
2008-10-08 09:35:02 +00:00
|
|
|
}
|
|
|
|
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
/* Alter reply tuple (maybe alter helper). */
|
2013-09-23 18:37:48 +00:00
|
|
|
void nf_conntrack_alter_reply(struct nf_conn *ct,
|
|
|
|
const struct nf_conntrack_tuple *newreply);
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
|
|
|
|
/* Is this tuple taken? (ignoring any belonging to the given
|
|
|
|
conntrack). */
|
2013-09-23 18:37:48 +00:00
|
|
|
int nf_conntrack_tuple_taken(const struct nf_conntrack_tuple *tuple,
|
|
|
|
const struct nf_conn *ignored_conntrack);
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
|
|
|
|
/* Return conntrack_info and tuple hash for given skb. */
|
|
|
|
static inline struct nf_conn *
|
|
|
|
nf_ct_get(const struct sk_buff *skb, enum ip_conntrack_info *ctinfo)
|
|
|
|
{
|
|
|
|
*ctinfo = skb->nfctinfo;
|
|
|
|
return (struct nf_conn *)skb->nfct;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* decrement reference count on a conntrack */
|
|
|
|
static inline void nf_ct_put(struct nf_conn *ct)
|
|
|
|
{
|
|
|
|
NF_CT_ASSERT(ct);
|
|
|
|
nf_conntrack_put(&ct->ct_general);
|
|
|
|
}
|
|
|
|
|
2006-03-22 21:56:08 +00:00
|
|
|
/* Protocol module loading */
|
2013-09-23 18:37:48 +00:00
|
|
|
int nf_ct_l3proto_try_module_get(unsigned short l3proto);
|
|
|
|
void nf_ct_l3proto_module_put(unsigned short l3proto);
|
2006-03-22 21:56:08 +00:00
|
|
|
|
2009-03-25 20:05:46 +00:00
|
|
|
/*
|
|
|
|
* Allocate a hashtable of hlist_head (if nulls == 0),
|
|
|
|
* or hlist_nulls_head (if nulls == 1)
|
|
|
|
*/
|
2013-09-23 18:37:48 +00:00
|
|
|
void *nf_ct_alloc_hashtable(unsigned int *sizep, int nulls);
|
2009-03-25 20:05:46 +00:00
|
|
|
|
2013-09-23 18:37:48 +00:00
|
|
|
void nf_ct_free_hashtable(void *hash, unsigned int size);
|
2007-07-08 05:30:08 +00:00
|
|
|
|
2013-09-23 18:37:48 +00:00
|
|
|
struct nf_conntrack_tuple_hash *
|
2010-02-15 17:13:33 +00:00
|
|
|
__nf_conntrack_find(struct net *net, u16 zone,
|
|
|
|
const struct nf_conntrack_tuple *tuple);
|
2006-01-05 20:19:05 +00:00
|
|
|
|
2013-09-23 18:37:48 +00:00
|
|
|
int nf_conntrack_hash_check_insert(struct nf_conn *ct);
|
2013-07-29 13:41:54 +00:00
|
|
|
bool nf_ct_delete(struct nf_conn *ct, u32 pid, int report);
|
2006-01-05 20:19:05 +00:00
|
|
|
|
2013-09-23 18:37:48 +00:00
|
|
|
void nf_conntrack_flush_report(struct net *net, u32 portid, int report);
|
2006-01-05 20:19:05 +00:00
|
|
|
|
2013-09-23 18:37:48 +00:00
|
|
|
bool nf_ct_get_tuplepr(const struct sk_buff *skb, unsigned int nhoff,
|
|
|
|
u_int16_t l3num, struct nf_conntrack_tuple *tuple);
|
|
|
|
bool nf_ct_invert_tuplepr(struct nf_conntrack_tuple *inverse,
|
|
|
|
const struct nf_conntrack_tuple *orig);
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
|
2013-09-23 18:37:48 +00:00
|
|
|
void __nf_ct_refresh_acct(struct nf_conn *ct, enum ip_conntrack_info ctinfo,
|
|
|
|
const struct sk_buff *skb,
|
|
|
|
unsigned long extra_jiffies, int do_acct);
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
|
|
|
|
/* Refresh conntrack for this many jiffies and do accounting */
|
|
|
|
static inline void nf_ct_refresh_acct(struct nf_conn *ct,
|
|
|
|
enum ip_conntrack_info ctinfo,
|
|
|
|
const struct sk_buff *skb,
|
|
|
|
unsigned long extra_jiffies)
|
|
|
|
{
|
|
|
|
__nf_ct_refresh_acct(ct, ctinfo, skb, extra_jiffies, 1);
|
|
|
|
}
|
|
|
|
|
|
|
|
/* Refresh conntrack for this many jiffies */
|
|
|
|
static inline void nf_ct_refresh(struct nf_conn *ct,
|
|
|
|
const struct sk_buff *skb,
|
|
|
|
unsigned long extra_jiffies)
|
|
|
|
{
|
|
|
|
__nf_ct_refresh_acct(ct, 0, skb, extra_jiffies, 0);
|
|
|
|
}
|
|
|
|
|
2013-09-23 18:37:48 +00:00
|
|
|
bool __nf_ct_kill_acct(struct nf_conn *ct, enum ip_conntrack_info ctinfo,
|
|
|
|
const struct sk_buff *skb, int do_acct);
|
2008-06-09 22:59:40 +00:00
|
|
|
|
|
|
|
/* kill conntrack and do accounting */
|
2008-07-15 03:22:38 +00:00
|
|
|
static inline bool nf_ct_kill_acct(struct nf_conn *ct,
|
|
|
|
enum ip_conntrack_info ctinfo,
|
|
|
|
const struct sk_buff *skb)
|
2008-06-09 22:59:40 +00:00
|
|
|
{
|
2008-07-15 03:22:38 +00:00
|
|
|
return __nf_ct_kill_acct(ct, ctinfo, skb, 1);
|
2008-06-09 22:59:40 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
/* kill conntrack without accounting */
|
2008-07-15 03:22:38 +00:00
|
|
|
static inline bool nf_ct_kill(struct nf_conn *ct)
|
2008-06-09 22:59:40 +00:00
|
|
|
{
|
2008-07-15 03:22:38 +00:00
|
|
|
return __nf_ct_kill_acct(ct, 0, NULL, 0);
|
2008-06-09 22:59:40 +00:00
|
|
|
}
|
2008-06-09 22:59:06 +00:00
|
|
|
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
/* These are for NAT. Icky. */
|
2013-07-28 20:54:10 +00:00
|
|
|
extern s32 (*nf_ct_nat_offset)(const struct nf_conn *ct,
|
2009-11-06 08:43:42 +00:00
|
|
|
enum ip_conntrack_dir dir,
|
|
|
|
u32 seq);
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
|
|
|
|
/* Fake conntrack entry for untracked connections */
|
2010-06-09 12:43:38 +00:00
|
|
|
DECLARE_PER_CPU(struct nf_conn, nf_conntrack_untracked);
|
2010-06-08 14:09:52 +00:00
|
|
|
static inline struct nf_conn *nf_ct_untracked_get(void)
|
|
|
|
{
|
2014-08-17 17:30:35 +00:00
|
|
|
return raw_cpu_ptr(&nf_conntrack_untracked);
|
2010-06-08 14:09:52 +00:00
|
|
|
}
|
2013-09-23 18:37:48 +00:00
|
|
|
void nf_ct_untracked_status_or(unsigned long bits);
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
|
|
|
|
/* Iterate over all conntracks: if iter returns true, it's deleted. */
|
2013-09-23 18:37:48 +00:00
|
|
|
void nf_ct_iterate_cleanup(struct net *net,
|
|
|
|
int (*iter)(struct nf_conn *i, void *data),
|
|
|
|
void *data, u32 portid, int report);
|
|
|
|
void nf_conntrack_free(struct nf_conn *ct);
|
|
|
|
struct nf_conn *nf_conntrack_alloc(struct net *net, u16 zone,
|
|
|
|
const struct nf_conntrack_tuple *orig,
|
|
|
|
const struct nf_conntrack_tuple *repl,
|
|
|
|
gfp_t gfp);
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
|
2010-02-03 13:13:03 +00:00
|
|
|
static inline int nf_ct_is_template(const struct nf_conn *ct)
|
|
|
|
{
|
|
|
|
return test_bit(IPS_TEMPLATE_BIT, &ct->status);
|
|
|
|
}
|
|
|
|
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
/* It's confirmed if it is, or has been in the hash table. */
|
|
|
|
static inline int nf_ct_is_confirmed(struct nf_conn *ct)
|
|
|
|
{
|
|
|
|
return test_bit(IPS_CONFIRMED_BIT, &ct->status);
|
|
|
|
}
|
|
|
|
|
|
|
|
static inline int nf_ct_is_dying(struct nf_conn *ct)
|
|
|
|
{
|
|
|
|
return test_bit(IPS_DYING_BIT, &ct->status);
|
|
|
|
}
|
|
|
|
|
2010-06-08 14:09:52 +00:00
|
|
|
static inline int nf_ct_is_untracked(const struct nf_conn *ct)
|
2007-03-14 23:37:25 +00:00
|
|
|
{
|
2010-06-08 14:09:52 +00:00
|
|
|
return test_bit(IPS_UNTRACKED_BIT, &ct->status);
|
2007-03-14 23:37:25 +00:00
|
|
|
}
|
|
|
|
|
2011-06-16 15:29:22 +00:00
|
|
|
/* Packet is received from loopback */
|
|
|
|
static inline bool nf_is_loopback_packet(const struct sk_buff *skb)
|
|
|
|
{
|
|
|
|
return skb->dev && skb->skb_iif && skb->dev->flags & IFF_LOOPBACK;
|
|
|
|
}
|
|
|
|
|
2011-08-29 17:21:14 +00:00
|
|
|
struct kernel_param;
|
|
|
|
|
2013-09-23 18:37:48 +00:00
|
|
|
int nf_conntrack_set_hashsize(const char *val, struct kernel_param *kp);
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
extern unsigned int nf_conntrack_htable_size;
|
2009-02-20 09:47:09 +00:00
|
|
|
extern unsigned int nf_conntrack_max;
|
2011-01-05 04:23:23 +00:00
|
|
|
extern unsigned int nf_conntrack_hash_rnd;
|
|
|
|
void init_nf_conntrack_hash_rnd(void);
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
|
netfilter: nf_conntrack: don't release a conntrack with non-zero refcnt
With this patch, the conntrack refcount is initially set to zero and
it is bumped once it is added to any of the list, so we fulfill
Eric's golden rule which is that all released objects always have a
refcount that equals zero.
Andrey Vagin reports that nf_conntrack_free can't be called for a
conntrack with non-zero ref-counter, because it can race with
nf_conntrack_find_get().
A conntrack slab is created with SLAB_DESTROY_BY_RCU. Non-zero
ref-counter says that this conntrack is used. So when we release
a conntrack with non-zero counter, we break this assumption.
CPU1 CPU2
____nf_conntrack_find()
nf_ct_put()
destroy_conntrack()
...
init_conntrack
__nf_conntrack_alloc (set use = 1)
atomic_inc_not_zero(&ct->use) (use = 2)
if (!l4proto->new(ct, skb, dataoff, timeouts))
nf_conntrack_free(ct); (use = 2 !!!)
...
__nf_conntrack_alloc (set use = 1)
if (!nf_ct_key_equal(h, tuple, zone))
nf_ct_put(ct); (use = 0)
destroy_conntrack()
/* continue to work with CT */
After applying the path "[PATCH] netfilter: nf_conntrack: fix RCU
race in nf_conntrack_find_get" another bug was triggered in
destroy_conntrack():
<4>[67096.759334] ------------[ cut here ]------------
<2>[67096.759353] kernel BUG at net/netfilter/nf_conntrack_core.c:211!
...
<4>[67096.759837] Pid: 498649, comm: atdd veid: 666 Tainted: G C --------------- 2.6.32-042stab084.18 #1 042stab084_18 /DQ45CB
<4>[67096.759932] RIP: 0010:[<ffffffffa03d99ac>] [<ffffffffa03d99ac>] destroy_conntrack+0x15c/0x190 [nf_conntrack]
<4>[67096.760255] Call Trace:
<4>[67096.760255] [<ffffffff814844a7>] nf_conntrack_destroy+0x17/0x30
<4>[67096.760255] [<ffffffffa03d9bb5>] nf_conntrack_find_get+0x85/0x130 [nf_conntrack]
<4>[67096.760255] [<ffffffffa03d9fb2>] nf_conntrack_in+0x352/0xb60 [nf_conntrack]
<4>[67096.760255] [<ffffffffa048c771>] ipv4_conntrack_local+0x51/0x60 [nf_conntrack_ipv4]
<4>[67096.760255] [<ffffffff81484419>] nf_iterate+0x69/0xb0
<4>[67096.760255] [<ffffffff814b5b00>] ? dst_output+0x0/0x20
<4>[67096.760255] [<ffffffff814845d4>] nf_hook_slow+0x74/0x110
<4>[67096.760255] [<ffffffff814b5b00>] ? dst_output+0x0/0x20
<4>[67096.760255] [<ffffffff814b66d5>] raw_sendmsg+0x775/0x910
<4>[67096.760255] [<ffffffff8104c5a8>] ? flush_tlb_others_ipi+0x128/0x130
<4>[67096.760255] [<ffffffff8100bc4e>] ? apic_timer_interrupt+0xe/0x20
<4>[67096.760255] [<ffffffff8100bc4e>] ? apic_timer_interrupt+0xe/0x20
<4>[67096.760255] [<ffffffff814c136a>] inet_sendmsg+0x4a/0xb0
<4>[67096.760255] [<ffffffff81444e93>] ? sock_sendmsg+0x13/0x140
<4>[67096.760255] [<ffffffff81444f97>] sock_sendmsg+0x117/0x140
<4>[67096.760255] [<ffffffff8102e299>] ? native_smp_send_reschedule+0x49/0x60
<4>[67096.760255] [<ffffffff81519beb>] ? _spin_unlock_bh+0x1b/0x20
<4>[67096.760255] [<ffffffff8109d930>] ? autoremove_wake_function+0x0/0x40
<4>[67096.760255] [<ffffffff814960f0>] ? do_ip_setsockopt+0x90/0xd80
<4>[67096.760255] [<ffffffff8100bc4e>] ? apic_timer_interrupt+0xe/0x20
<4>[67096.760255] [<ffffffff8100bc4e>] ? apic_timer_interrupt+0xe/0x20
<4>[67096.760255] [<ffffffff814457c9>] sys_sendto+0x139/0x190
<4>[67096.760255] [<ffffffff810efa77>] ? audit_syscall_entry+0x1d7/0x200
<4>[67096.760255] [<ffffffff810ef7c5>] ? __audit_syscall_exit+0x265/0x290
<4>[67096.760255] [<ffffffff81474daf>] compat_sys_socketcall+0x13f/0x210
<4>[67096.760255] [<ffffffff8104dea3>] ia32_sysret+0x0/0x5
I have reused the original title for the RFC patch that Andrey posted and
most of the original patch description.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Andrew Vagin <avagin@parallels.com>
Cc: Florian Westphal <fw@strlen.de>
Reported-by: Andrew Vagin <avagin@parallels.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Andrew Vagin <avagin@parallels.com>
2014-02-03 19:01:53 +00:00
|
|
|
void nf_conntrack_tmpl_insert(struct net *net, struct nf_conn *tmpl);
|
|
|
|
|
2012-04-18 04:36:40 +00:00
|
|
|
#define NF_CT_STAT_INC(net, count) __this_cpu_inc((net)->ct.stat->count)
|
|
|
|
#define NF_CT_STAT_INC_ATOMIC(net, count) this_cpu_inc((net)->ct.stat->count)
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
|
2008-11-17 15:01:42 +00:00
|
|
|
#define MODULE_ALIAS_NFCT_HELPER(helper) \
|
|
|
|
MODULE_ALIAS("nfct-helper-" helper)
|
|
|
|
|
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2005-11-10 00:38:16 +00:00
|
|
|
#endif /* _NF_CONNTRACK_H */
|